NICE RUN 1800 RUN1800 Sliding Gate Motor – 1800 KG

NICE RUN1800 Heavy-Duty Industrial Sliding Gate Motor UAE

The NICE RUN 1800 RUN1800 is a professional heavy-duty industrial automatic sliding gate motor designed for gates weighing up to 1800 KG and measuring up to 15 metres in length. Built for demanding sliding gate automation, the RUN1800 combines a powerful single-phase asynchronous motor, NICE BlueBUS communication, advanced electronic control and intensive-use capability.

With up to 40 Nm maximum start-up torque, approximately 1110 N maximum force and a no-load speed of 10 m/min, the NICE RUN1800 provides strong and reliable automatic movement for large residential, commercial and industrial sliding gates. It is suitable for warehouses, factories, logistics facilities, residential compounds, commercial properties and heavy vehicle entrances throughout the UAE.

NICE RUN 1800 Key Features

• Heavy-duty industrial sliding gate motor
• Suitable for sliding gates weighing up to 1800 KG
• Maximum gate length up to 15 metres
• 230V AC single-phase asynchronous motor
• Maximum start-up power: 700 W
• Power at nominal torque: 400 W
• Maximum start-up current: 3 A
• Current at nominal torque: 1.8 A
• Maximum start-up torque: 40 Nm
• Maximum corresponding force: 1110 N
• Nominal torque: 20 Nm
• Nominal corresponding force: 560 N
• No-load speed: 10 m/min – approx. 0.17 m/s
• Speed at nominal torque: 8.5 m/min – approx. 0.14 m/s
• Up to 42 cycles/hour for gates up to 6 metres
• Maximum continuous operation up to 40 minutes at nominal torque under specified conditions
• NICE BlueBUS communication technology
• Automatic gate-length learning
• Automatic calculation of slowdown points
• Automatic calculation of partial-opening position
• Electronic obstacle detection
• Master/Slave operation for opposing sliding gates
• Temperature-controlled heating and cooling management
• Electromechanical limit switch on RUN1800
• Inductive proximity limit switch on RUN1800P
• SM connector for compatible NICE radio receiver
• BusT4 connection for NICE Oview programming
• IP44 protection rating

NICE RUN1800 Technical Specifications

Heavy-Duty 1800 KG Sliding Gate Automation

The NICE RUN1800 is designed for heavy sliding gate applications where smaller residential motors do not provide sufficient capacity. NICE specifies a maximum sliding gate weight of 1800 KG and a maximum leaf length of 15 metres.

The RUN1800 produces up to 40 Nm maximum starting torque, corresponding to approximately 1110 N maximum force. Its nominal operating torque is 20 Nm, corresponding to approximately 560 N.

700 W Maximum Start-Up Power

The NICE RUN1800 should not simply be described as a continuously rated 700 W motor. NICE specifies 700 W maximum power absorption during start-up, while power at nominal operating torque is approximately 400 W.

The corresponding electrical current is approximately 3 A at maximum start-up and approximately 1.8 A at nominal torque.

NICE RUN1800 Gate Speed

The NICE RUN 1800 has a no-load travel speed of approximately 10 metres per minute, equivalent to about 0.17 m/s. At nominal torque, NICE specifies approximately 8.5 metres per minute, equivalent to around 0.14 m/s.

For SEO and technical accuracy, it is better to show both values rather than listing only 0.17 m/s as if it were the operating speed under every load condition.

NICE RUN1800 Operating Cycles by Gate Length

These figures apply according to gate length. Gate weight further reduces the permitted cycle frequency, so motor selection should consider both gate length and gate weight.

Operating Limits According to Gate Weight

This means that a RUN1800 installed on a gate near its maximum 1800 KG rating cannot operate at the same duty level as the same motor installed on a much lighter gate.

Important UAE Climate Consideration

The NICE RUN1800 control system monitors motor load and ambient temperature and can reduce the permitted number of manoeuvres when conditions become demanding. NICE specifically includes ambient temperatures above 40°C, dust, sand, high humidity and salinity among factors that can increase operating severity.

This is particularly relevant for outdoor sliding gate installations in the UAE. Correct motor sizing, ventilation, mechanical gate condition and periodic maintenance are important for reliable operation in hot and dusty environments.

NICE BlueBUS Technology

The NICE RUN1800 sliding gate motor incorporates NICE BlueBUS technology. Compatible safety and automation devices can communicate with the control system using only two wires for both power and data.

The RUN control system provides one BlueBUS output supporting a maximum load of up to 15 BlueBUS units. This can simplify professional installation of compatible photocells and safety devices.

Automatic Device Learning

The RUN1800 control unit can automatically recognise compatible devices connected to the BlueBUS and STOP inputs during setup.

After accessories are installed or changed, the self-learning procedure allows the control system to update the connected device configuration.

Automatic Gate Length Learning

The NICE RUN1800 automatically learns the sliding gate travel between the opening and closing limit switches. This measurement is then used by the control system to calculate important operating parameters.

These include slowdown positions and the partial-opening position, helping provide controlled automatic gate movement after professional commissioning.

Electronic Obstacle Detection

The RUN1800 electronically monitors gate movement and can detect abnormal resistance. If excessive friction or an obstacle is detected, the control system can respond according to its programmed safety logic.

This feature should always be combined with correctly installed photocells, safety edges and other protection devices required for the specific gate installation.

Electromechanical Limit Switch – RUN1800

The standard RUN1800 uses an electromechanical limit switch system. NICE also manufactures the RUN1800P version, which uses an inductive proximity limit switch.

These two versions should not be confused. If your product page is specifically for RUN1800, describe the limit switch as electromechanical.

Master / Slave Dual Sliding Gate Operation

The NICE RUN control system supports Master/Slave operation. Two compatible motors can be configured for synchronized operation on opposing sliding gate leaves.

This is useful for wide commercial, industrial and compound entrances where two sliding leaves meet in the centre.

Temperature-Controlled Motor Management

The NICE RUN platform incorporates temperature monitoring that helps manage motor force, thermal protection and self-ventilation according to operating conditions.

This allows the automation system to adapt its operation to changing environmental conditions while protecting the motor from excessive thermal stress.

BusT4 & NICE Oview Programming

The RUN1800 includes a BusT4 connector for compatible NICE Oview programming equipment. Professional technicians can use this interface for installation management, configuration, maintenance and troubleshooting.

Compatible NICE OXI or OXIT receivers can also be accessed through the programming system when installed.

NICE RUN1800 Radio Receiver Compatibility

The RUN control board includes an SM-type connector for compatible NICE radio receivers. NICE documentation lists receivers such as SMXI, SMXIS and ONEXI, while later installations may also use compatible NICE OXI-family radio equipment according to the installed system.

NICE RUN1800 Compatible Accessories

• NICE compatible radio receiver
• NICE remote controls
• NICE BlueBUS photocell sensors
• NICE flashing warning lights
• NICE Oview programming interface
• Safety edges
• Key selector switches
• Push button switches
• Steel gate gear racks
• Heavy-duty nylon gear racks where appropriate
• GSM gate opener systems
• Wi-Fi gate controllers
• RFID access control systems
• UHF long-range RFID readers
• Vehicle loop detectors
• Intercom and vehicle access systems

NICE RUN1800 Package

• 1 × NICE RUN1800 Heavy-Duty Sliding Gate Motor
• 1 × Integrated Electronic Control Unit
• 2 × NICE Remote Controls
• 1 × NICE EPMB BlueBUS Photocell Pair
• 1 × NICE OXI Compatible Radio Receiver
• 1 × Flashing Warning Light
• 1 × Push Button

Note: Package contents can vary according to stock and supplied configuration. Confirm the exact motor accessories, receiver, remotes, photocells and flashing light before ordering.

NICE RUN1800 Applications

• Heavy villa sliding gates
• Residential compounds
• Gated communities
• Commercial sliding gates
• Warehouse entrances
• Factory sliding gates
• Industrial entrances
• Logistics facilities
• Commercial parking entrances
• Controlled vehicle access points
• Heavy sliding gates up to 1800 KG
• Long sliding gates up to 15 metres

NICE RUN1800 for Commercial & Industrial Gates

The NICE RUN1800 is particularly suited to heavy commercial and industrial sliding gates. Its 1800 KG capacity, strong 1110 N maximum force and intelligent duty-cycle management make it suitable for many demanding entrances.

Warehouses, logistics facilities, factories, commercial compounds and controlled parking entrances can benefit from the combination of high gate capacity and advanced Nice electronic control.

NICE RUN1800 for Large Villas UAE

The RUN1800 can also be used on large UAE villa sliding gates where the gate is exceptionally heavy or long. However, the motor should not be selected only because it has a high maximum weight rating.

Gate wheels, track condition, rack alignment, rolling resistance, gate structure and expected operating frequency should all be professionally checked before installation.

NICE RUN1800 vs RUN1500

The NICE RUN1800 provides a higher gate weight capacity than the RUN1500. RUN1800 is rated up to 1800 KG, while RUN1500 is intended for gates up to 1500 KG.

RUN1800 also uses a robust 230V single-phase asynchronous motor and is designed for demanding industrial sliding gate applications. The correct motor should be chosen according to actual gate weight, length, operating frequency and site conditions.

NICE RUN1800 vs RUN1800P

The RUN1800 and RUN1800P have the same 1800 KG maximum gate weight and 15 m maximum gate length, but their limit-switch systems are different.

RUN1800 uses an electromechanical limit switch, while RUN1800P uses an inductive proximity limit switch. Make sure the exact model supplied matches the product page and spare parts selected.

Professional NICE RUN1800 Installation UAE

Professional installation of the NICE RUN 1800 RUN1800 sliding gate motor is available throughout the UAE. Installation can include gate inspection, foundation preparation, motor mounting, rack installation, limit-switch adjustment, BlueBUS photocell installation, radio receiver setup, remote programming and complete electronic commissioning.

After installation, the system should be tested for gate movement, motor force, stopping positions, obstacle detection, photocell operation, remote controls, safety functions and manual emergency release.

NICE RUN1800 Repair & Spare Parts UAE

Technical support is available for NICE RUN1800 repair, programming, maintenance and spare parts. Compatible components can include control electronics, NICE radio receivers, remote controls, BlueBUS photocells, limit-switch components, flashing lights, safety accessories and gate racks.

Professional fault diagnosis is recommended before replacing electronic or mechanical components.

Why Choose NICE RUN 1800?

• Heavy-duty NICE industrial gate automation
• Suitable for sliding gates up to 1800 KG
• Supports gates up to 15 metres long
• 40 Nm maximum start-up torque
• 1110 N maximum force
• 20 Nm / 560 N nominal torque and force
• 700 W maximum start-up power
• 400 W power at nominal torque
• Up to 42 cycles/hour with gates up to 6 metres
• BlueBUS communication technology
• Automatic gate-length learning
• Automatic slowdown calculation
• Electronic obstacle detection
• Master/Slave dual-gate function
• Temperature-controlled motor management
• BusT4 / Oview programming compatibility
• IP44 protection
• Professional UAE installation available

Buy NICE RUN 1800 RUN1800 Gate Motor UAE

Buy the NICE RUN 1800 RUN1800 heavy-duty sliding gate motor in UAE for reliable commercial and industrial gate automation. Contact us for product availability, UAE delivery, professional installation, programming, maintenance and NICE gate motor spare parts.

Supply and installation support is available across Dubai, Sharjah, Abu Dhabi, Ajman, Al Ain, Ras Al Khaimah, Fujairah and Umm Al Quwain.

Frequently Asked Questions

What is the maximum gate weight for NICE RUN1800?
The NICE RUN1800 is designed for compatible sliding gates weighing up to 1800 KG.

What is the maximum gate length for NICE RUN1800?
Nice specifies a maximum gate leaf length of 15 metres.

What is the power of NICE RUN1800?
Nice specifies 700 W maximum power absorption during start-up and approximately 400 W at nominal torque.

What is the maximum force of NICE RUN1800?
The RUN1800 provides up to approximately 1110 N maximum force, corresponding to 40 Nm maximum start-up torque.

What is the nominal force of NICE RUN1800?
Nominal force is approximately 560 N, corresponding to 20 Nm nominal torque.

How fast is NICE RUN1800?
The no-load speed is approximately 10 m/min or 0.17 m/s. At nominal torque, speed is approximately 8.5 m/min or 0.14 m/s.

How many cycles per hour can NICE RUN1800 perform?
Nice specifies up to 42 cycles/hour for gates up to 6 metres. Longer and heavier gates require a lower operating frequency.

Can NICE RUN1800 perform 42 cycles/hour with an 1800 KG gate?
Not necessarily. Gate weight reduces the permitted operating cycle percentage. For gates between 1500 and 1800 KG, Nice specifies a 50% cycle factor.

Does NICE RUN1800 support BlueBUS?
Yes. The RUN1800 supports NICE BlueBUS and can manage compatible BlueBUS safety and control devices through a two-wire connection.

What type of limit switch does NICE RUN1800 use?
The standard RUN1800 uses an electromechanical limit switch. RUN1800P uses an inductive proximity limit switch.

Can NICE RUN1800 operate two opposing sliding gates?
Yes. The RUN system supports Master/Slave configuration for compatible opposing sliding gate installations.

Is NICE RUN1800 suitable for industrial gates?
Yes. Nice officially describes RUN1800 as an electromechanical gearmotor for automatic movement of sliding gates for industrial use.

Do you provide NICE RUN1800 installation in UAE?
Yes. Professional installation and technical support are available throughout the UAE.