NICE RUN 2500 RUN2500 Sliding Gate Motor – 2500 KG

NICE RUN2500 Heavy-Duty Industrial Sliding Gate Motor UAE

The NICE RUN 2500 RUN2500 is a professional heavy-duty industrial automatic sliding gate motor designed for sliding gates weighing up to 2500 KG and measuring up to 18 metres in length. Manufactured by NICE Italy for demanding industrial automation, the RUN2500 combines exceptional mechanical strength, intensive-duty performance, NICE BlueBUS technology and advanced electronic gate control.

With a maximum starting torque of 50 Nm, equivalent to approximately 1390 N maximum force, and nominal torque of 30 Nm / 830 N, the NICE RUN2500 is designed for extremely heavy sliding gates at factories, warehouses, logistics centres, commercial compounds, ports and large controlled vehicle entrances throughout the UAE.

NICE RUN 2500 Key Features

• Heavy-duty industrial automatic sliding gate motor
• Suitable for sliding gates weighing up to 2500 KG
• Maximum gate leaf length up to 18 metres
• 230V AC single-phase asynchronous motor
• Ventilated motor for demanding operating conditions
• Maximum start-up power: 870 W
• Power at nominal torque: 600 W
• Maximum start-up current: 3.8 A
• Current at nominal torque: 2.7 A
• Maximum start-up torque: 50 Nm
• Maximum corresponding force: 1390 N
• Nominal torque: 30 Nm
• Nominal corresponding force: 830 N
• No-load speed: 10 m/min – approximately 0.17 m/s
• Maximum operating frequency depends on gate length and weight
• Up to 42 cycles/hour for gates up to 6 metres
• Maximum continuous operation: 60 minutes at nominal torque
• NICE BlueBUS communication technology
• Supports up to 15 BlueBUS units
• Automatic gate length learning
• Automatic calculation of slowdown points
• Automatic calculation of partial opening position
• Electronic obstacle detection
• Adjustable acceleration and deceleration
• Master/Slave operation for compatible opposing gates
• Adaptive temperature management
• Automatic motor ventilation management
• Electromechanical limit switch on RUN2500
• Inductive proximity limit switch on RUN2500P
• SM connector for compatible NICE radio receiver
• IP44 weather protection

NICE RUN2500 Technical Specifications

Brand	NICE
Series	RUN
Model	RUN2500
Product Type	Heavy-Duty Industrial Sliding Gate Motor
Maximum Gate Weight	2500 KG
Maximum Gate Length	18 Metres
Power Supply	230V AC (+10% / -15%), 50 Hz
Motor Type	Single-Phase Asynchronous Ventilated Motor
Maximum Start-Up Power	870 W
Power at Nominal Torque	600 W
Maximum Start-Up Current	3.8 A
Current at Nominal Torque	2.7 A
Maximum Start-Up Torque	50 Nm
Maximum Force	1390 N
Nominal Torque	30 Nm
Nominal Force	830 N
No-Load Speed	10 m/min – Approx. 0.17 m/s
Maximum Cycles / Hour	Up to 42 Cycles/Hour for Gates up to 6 m
Maximum Continuous Operation	60 Minutes at Nominal Torque
Limit Switch	Electromechanical – RUN2500
Communication	NICE BlueBUS
Maximum BlueBUS Load	15 BlueBUS Units
Radio Receiver Connector	SM Connector
Pinion	Z18 – Module 4
Protection Rating	IP44
Operating Temperature	-20°C to +50°C
Dimensions	400 × 255 × 390 mm
Weight	24.5 KG
Country of Origin	Italy

2500 KG Heavy-Duty Industrial Gate Automation

The NICE RUN2500 is one of the strongest conventional sliding gate operators in the NICE RUN range. It is designed for compatible sliding gates weighing up to 2500 KG, making it suitable for extra-heavy industrial and commercial gate installations.

The RUN2500 provides up to 50 Nm maximum start-up torque, equivalent to approximately 1390 N maximum force. Its nominal operating torque is 30 Nm, corresponding to approximately 830 N.

Maximum Gate Length up to 18 Metres

NICE specifies the RUN2500 and RUN2500P for compatible sliding gate leaves measuring up to 18 metres. This makes the RUN2500 suitable for very wide industrial entrances where both high gate weight and long travel distance must be considered.

Gate length has a direct effect on operating frequency. A long 18-metre gate cannot perform the same number of cycles per hour as a shorter 4 or 6-metre gate.

870 W Maximum Start-Up Power

The NICE RUN 2500 should not simply be described as an 870 W continuous motor. NICE specifies 870 W maximum power absorption during start-up, corresponding to approximately 3.8 A.

At nominal operating torque, the motor consumes approximately 600 W / 2.7 A. Showing both figures provides more accurate technical information than listing only 870 W.

1390 N Maximum Gate Force

The RUN2500 produces a maximum start-up torque of 50 Nm, corresponding to approximately 1390 N maximum force. This provides the starting strength required for correctly installed extra-heavy sliding gates.

During normal movement the nominal torque is approximately 30 Nm, corresponding to approximately 830 N nominal force.

NICE RUN2500 Gate Speed

The NICE RUN2500 industrial sliding gate motor provides a no-load movement speed of approximately 10 metres per minute, equivalent to about 0.17 metres per second.

Actual gate movement speed depends on gate weight, mechanical resistance, operating conditions and the motor load. The no-load figure should therefore not be presented as a guaranteed speed for every 2500 KG installation.

NICE RUN2500 Operating Cycles by Gate Length

Gate Length	Maximum Cycles / Hour	Maximum Consecutive Cycles
Up to 6 m	42	42
6 – 9 m	28	28
9 – 12 m	21	21
12 – 15 m	17	17
15 – 18 m	14	14

The cycle figures above are maximum values based on gate length. The gate weight must also be considered because heavier gates reduce the permitted operating frequency.

NICE RUN2500 Operating Limits by Gate Weight

Gate Weight	Permitted Cycle Percentage
Up to 500 KG	100%
500 – 900 KG	80%
900 – 1200 KG	75%
1200 – 1500 KG	60%
1500 – 1800 KG	50%
2000 – 2300 KG	40%
2300 – 2500 KG	30%

For gates approaching the full 2500 KG rating, the available duty cycle is therefore considerably lower than for a lighter gate. Motor selection should always be based on both gate weight and gate length.

Maximum Continuous Operation up to 60 Minutes

NICE specifies a maximum continuous operating time of approximately 60 minutes at nominal torque for RUN2500 under the stated test conditions.

This makes the RUN2500 suitable for demanding industrial applications, but continuous operating capacity is still affected by gate size, gate weight and ambient temperature.

Important UAE Temperature Consideration

The RUN2500 includes motor temperature management and ventilation to support demanding operating conditions. However, high ambient temperature can reduce permissible operating frequency.

This is particularly relevant for outdoor industrial gate installations in the UAE. Correct gate sizing, motor ventilation, track condition, wheel maintenance and periodic servicing are important for reliable performance during hot weather.

Ventilated Industrial Motor

The NICE RUN2500 uses a ventilated single-phase asynchronous motor designed for demanding gate automation. Motor ventilation helps manage operating temperature during intensive applications.

The system's temperature management works together with the electronic control system to help protect the motor during heavy use.

NICE BlueBUS Technology

The RUN2500 incorporates NICE BlueBUS technology. Compatible safety and control devices can communicate with the gate control system using a simplified two-wire connection carrying both power and communication signals.

The BlueBUS output supports a maximum load of up to 15 BlueBUS units, allowing compatible photocells and other supported accessories to be integrated with reduced wiring complexity.

Automatic Device Learning

The NICE RUN2500 control system can automatically learn compatible devices connected to the BlueBUS output. It can also identify the type of device connected to the STOP input.

This simplifies professional setup when compatible photocells, safety edges or control devices are installed or changed.

Automatic Gate Length Learning

The RUN2500 automatically learns the travel length of the sliding gate during commissioning. The system then calculates appropriate slowdown positions and the partial-opening position.

This allows the automation to adapt its movement according to the actual gate travel instead of relying only on fixed timer settings.

Electronic Obstacle Detection

The NICE RUN2500 electronically monitors motor effort during gate movement. Abnormal resistance can be detected and processed by the control system according to the programmed safety logic.

Electronic obstacle detection should always be combined with correctly installed photocells, safety edges and other safety devices appropriate for the gate installation.

Adjustable Acceleration & Deceleration

The NICE RUN platform provides configurable acceleration and slowdown behaviour. Smooth acceleration reduces sudden mechanical stress when an extremely heavy gate begins moving, while deceleration provides more controlled movement as the gate approaches its opening or closing position.

This is particularly useful for industrial gates where excessive mechanical impact can increase wear on racks, wheels, tracks and gate structures.

Electromechanical Limit Switch – RUN2500

The standard NICE RUN2500 uses an electromechanical limit switch system.

The RUN2500P is a different version and uses an inductive proximity limit switch. These models should be kept clearly separated when listing products or ordering spare parts.

Master / Slave Dual Sliding Gate Operation

The NICE RUN system supports Master/Slave operation for compatible opposing sliding gates. Two motors can be configured to operate together as one synchronized entrance.

This can be useful for extremely wide industrial entrances, logistics centres, compounds and other sites using two sliding gate leaves.

SM Radio Receiver Connector

The RUN2500 control system provides an SM connector for compatible NICE radio receivers. NICE documentation lists compatible receiver families such as SMXI, SMXIS and ONEXI, depending on the system generation.

Compatible NICE radio equipment and remote controls can be selected according to the receiver fitted to the motor.

NICE RUN2500 Compatible Accessories

• NICE compatible SM / OXI radio receiver according to configuration
• NICE remote controls
• NICE EPMB BlueBUS photocells
• NICE BlueBUS safety accessories
• NICE flashing warning lights
• Safety edges
• Push button switches
• Key selector switches
• Heavy-duty steel gate racks
• Compatible nylon gate racks where appropriate
• GSM gate opener systems
• Wi-Fi gate control systems
• RFID access control systems
• UHF long-range RFID readers
• Vehicle loop detectors
• ANPR vehicle access systems
• Intercom systems

NICE RUN2500 Package

• 1 × NICE RUN2500 2500 KG Sliding Gate Motor
• 1 × Integrated Electronic Control Unit
• 2 × NICE ON2E Remote Controls
• 1 × NICE EPMB BlueBUS Photocell Pair
• 1 × NICE OXI Compatible Radio Receiver
• 1 × Flashing Warning Light
• 1 × Push Button

Note: Package contents can vary according to supplied stock and kit configuration. Confirm the exact motor, control board, receiver, remote controls, photocells and other included accessories before ordering.

NICE RUN2500 Applications

• Extra-heavy industrial sliding gates
• Factories and manufacturing facilities
• Warehouses
• Distribution centres
• Logistics facilities
• Industrial compounds
• Commercial complexes
• Ports and shipyards
• Freight terminals
• High-security entrances
• Heavy vehicle access gates
• Large parking entrances
• Sliding gates up to 2500 KG
• Sliding gates up to 18 metres long

NICE RUN2500 for Industrial Gates UAE

The NICE RUN2500 2500 KG gate motor is particularly suitable for demanding industrial sliding gate applications in the UAE. Its combination of 2500 KG gate capacity, 1390 N maximum force, ventilated motor and BlueBUS electronic control provides a strong solution for large vehicle entrances.

Typical installations include factories, warehouses, logistics hubs, distribution facilities and commercial compounds where reliable access automation is required.

NICE RUN2500 for Ports & Logistics Facilities

Large logistics sites frequently use wide, heavy sliding gates designed for truck and commercial vehicle access. The RUN2500's 18 m maximum gate length and 2500 KG gate capacity make it suitable for many of these applications when operating limits are correctly calculated.

For gates exposed to heavy traffic, motor selection should be based on gate size, weight, cycles per hour, wind loading, track condition and ambient temperature.

NICE RUN2500 vs RUN1800

The NICE RUN2500 provides substantially greater capacity than the RUN1800. RUN1800 is designed for gates up to approximately 1800 KG / 15 m, while RUN2500 increases capacity to 2500 KG / 18 m.

RUN2500 also provides up to 50 Nm / 1390 N maximum starting torque and force, compared with the lower rating of RUN1800. For extremely heavy or long sliding gates, RUN2500 is the more appropriate option when all operating limits are met.

NICE RUN2500 vs RUN2500P

The RUN2500 and RUN2500P share the same basic 2500 KG gate capacity and 18 m maximum gate length. Their main difference is the limit switch system.

RUN2500 uses an electromechanical limit switch, while RUN2500P uses an inductive proximity limit switch.

NICE RUN2500 vs RUN2500I

The standard NICE RUN2500 should also be kept separate from the RUN2500I inverter model. RUN2500I uses integrated inverter technology and has different electronic and performance characteristics.

If both products are sold on your website, maintaining separate product pages helps customers identify the correct motor and also targets different product searches more accurately.

Professional NICE RUN2500 Installation UAE

Professional installation of the NICE RUN 2500 RUN2500 industrial sliding gate motor is available throughout the UAE. Installation can include gate inspection, foundation preparation, motor mounting, heavy-duty rack installation, limit-switch adjustment, BlueBUS photocell installation, radio receiver setup, remote-control programming and complete electronic commissioning.

For a 2500 KG industrial gate, the condition of the wheels, track and structure is extremely important. The gate should move smoothly by hand before the motor is installed.

NICE RUN2500 Repair & Spare Parts UAE

Technical support is available for NICE RUN2500 repair, programming, maintenance and spare parts. Compatible replacement items can include control electronics, radio receivers, remote controls, BlueBUS photocells, limit-switch components, flashing lights, safety accessories, rack sections and other mechanical parts.

Professional diagnosis is recommended before replacing electronic or mechanical components, especially on intensive-use industrial gate systems.

Why Choose NICE RUN 2500?

• Extra-heavy-duty NICE industrial gate motor
• Suitable for sliding gates up to 2500 KG
• Maximum gate leaf length up to 18 metres
• 50 Nm maximum starting torque
• 1390 N maximum starting force
• 30 Nm / 830 N nominal torque and force
• 870 W maximum start-up power
• 600 W power at nominal torque
• Ventilated motor design
• Up to 60 minutes continuous operation at nominal torque
• BlueBUS communication
• Up to 15 BlueBUS units
• Automatic gate travel learning
• Electronic obstacle detection
• Adjustable acceleration and deceleration
• Master/Slave dual-gate function
• Industrial construction
• Professional UAE installation available

Buy NICE RUN 2500 RUN2500 Gate Motor UAE

Buy the NICE RUN 2500 RUN2500 2500 KG sliding gate motor in UAE for powerful and reliable industrial gate automation. Contact us for product availability, UAE delivery, professional installation, programming, maintenance and NICE gate motor spare parts.

Supply and installation support is available across Dubai, Sharjah, Abu Dhabi, Ajman, Al Ain, Ras Al Khaimah, Fujairah and Umm Al Quwain.

Frequently Asked Questions

What is the maximum gate weight for NICE RUN2500?
The NICE RUN2500 is designed for compatible sliding gates weighing up to 2500 KG.

What is the maximum gate length for NICE RUN2500?
NICE specifies a maximum sliding gate leaf length of 18 metres.

What is the maximum force of NICE RUN2500?
The RUN2500 provides up to approximately 1390 N maximum starting force, corresponding to 50 Nm maximum start-up torque.

What is the nominal force of NICE RUN2500?
The nominal force is approximately 830 N, corresponding to 30 Nm nominal torque.

What is the power of NICE RUN2500?
NICE specifies 870 W / 3.8 A maximum at start-up and approximately 600 W / 2.7 A at nominal torque.

How fast is NICE RUN2500?
The no-load gate speed is approximately 10 m/min or 0.17 m/s. Actual speed can vary according to gate load and installation conditions.

How many cycles per hour can NICE RUN2500 perform?
For gates up to 6 metres long, NICE specifies up to 42 cycles/hour. The permitted frequency reduces as gate length and weight increase.

Can RUN2500 perform 42 cycles/hour on a 2500 KG gate?
No. The maximum cycle figure must be reduced according to gate weight. For gates between 2300 and 2500 KG, NICE specifies a 30% duty factor relative to the applicable gate-length cycle limit.

What is the maximum continuous operating time?
NICE specifies up to approximately 60 minutes continuous operation at nominal torque under the stated test conditions.

Does NICE RUN2500 support BlueBUS?
Yes. The RUN2500 supports NICE BlueBUS and can manage up to 15 compatible BlueBUS units.

What type of limit switch does NICE RUN2500 use?
The standard RUN2500 uses an electromechanical limit switch. The RUN2500P version uses an inductive proximity limit switch.

Is NICE RUN2500 suitable for industrial gates?
Yes. NICE classifies the RUN2500 as an electromechanical gearmotor for automatic movement of industrial sliding gates.

Do you provide NICE RUN2500 installation in UAE?
Yes. Professional installation, programming, maintenance and technical support are available throughout the UAE.